一、BIOS中的提示信息

提示信息 說明
Drive A error 驅動器A錯誤
System halt 系統掛起
Keyboard controller error 鍵盤控制器錯誤
Keyboard error or no keyboard present 鍵盤錯誤或者鍵盤不存在
BIOS ROM checksum error BIOS　ROM 校驗錯誤
Single hardisk cable fail 當硬盤使用Cable選項時硬盤安裝位置不正確
FDD Controller Failure BIOS 軟盤控制器錯誤
HDD Controller Failure BIOS 硬盤控制器錯誤
Driver Error 驅動器錯誤
Cache Memory Bad, Do not Enable Cache 高速緩存Cache損壞，不能使用
Error: Unable to control A20 line 錯誤提示：不能使用A20地址控制線
Memory write/Read failure 內存讀寫失敗
Memory allocation error 內存定位錯誤
CMOS Battery state Low CMOS沒電了
Keyboard interface error 鍵盤接口錯誤
Hard disk drive failure 加載硬盤失敗
Hard disk not present 硬盤不存在
Floppy disk(s) fail (40) 軟盤驅動器加載失敗，一般是數據線插反，電源線沒有插接，CMOS內部軟驅設置錯誤
CMOS checksum error-efaults loaded. CMOS校驗錯誤，裝入缺省(默認)設置

　二、BIOS刷新失敗后，Bootblock啟動時出現的提示信息

提示信息 說明
Detecting floppy drive A media... 檢測軟驅A的格式
Drive media is : 1.44Mb1.2Mb 720Kb 360K 驅動器格式是1.44Mb、12Mb、720kb、360kb的一種
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER 磁盤引導失敗，插入系統盤后按任意鍵繼續

三、MBR主引導區提示信息

提示信息 說明
Invalid partition table 無效的分區表
Error loading operating sy stem 不能裝入引導系統
Missing operating system 系統引導文件丟失

　　說明：如果在計算機啟動過程中，在硬件配置清單下方(也就時在平時正常啟動時出現Starting Windows 98…的地方)出現不可識別字符，此時可判斷硬盤分區表?yè)p壞。如果你的硬盤上有重要資料，這時你不要輕易進行分區，可找專業的數據恢復公司。
　　四、DOS活動分區中的提示信息

提示信息 說明
Invalid system disk 無效的系統盤
Disk I/O error, Replace the disk and press any key. 磁盤I/O錯誤，替換磁盤后按任意鍵(當C盤系統文件丟失或被破壞時出現該提示信息。這時可能SYS C:為修復系統文件)
Invalid Media Type reaching Drive C: 無效的Ｃ盤媒體格式說明。也就是C盤沒有格式化或者是其他操作系統的磁盤格式如NTFS
Invalid Boot Diskette Boot Failure 無效的啟動盤，啟動失敗

　　五、IO.SYS中的提示信息

提示信息 說明
Insert diskette for drive and press any key when ready 插入磁盤到驅動器中后按任意鍵
Your program caused a divide overflow error
If the problem persists, contact your program vendor 你的程序?qū)е乱绯鲥e(cuò)誤。如果該問題還存在，請聯系你的程序供應商
Windows has disabled direct disk access to protect your long filenames Windows不能直接訪問受保護的長文件名
The system has been halted. Press Ctrl+Alt+Del to restart your computer 系統掛起，按Ctrl+Alt+Del重新啟動你的計算機
You started your computer with a version of MS-DOS incompatible with this version of Windows. Insert a Startup diskette matching this version of Windows and then restart 你啟動的MS-DOS版本與Windows版本不兼容，請插入與Windows版本匹配的系統盤后再重啟
This version of Windows requires a 386 or better processor 該Windows版本需要386以后的CPU支持
A20 hardware error. Contact technical support to identify the problem 地址線A20錯誤。聯系技術支持來識別該問題
Starting Windows 98... 正在啟動Windows 98……
Windows 98 is now starting your MS-DOS-based program Windows 98正在啟動基于MS-DOS的程序
Windows 98 is now restarting... Windows 98正在重新啟動
Press Esc now to cancel MS-DOS mode and restart Windows 98... 按Esc退出MS-DOS 模式，重新啟動Windows 98…
There is an unrecognized command in your CONFIG.SYS file 在你的CONFIG.SYS文件中有不可識別的命令
The following command in your CONFIG.SYS file is incorrect: 在你的CONFIG.SYS有下列錯誤命令
The sector size specified in this file is too large: 該文件中指定的扇區太大
The following file is missing or corrupted: WIN.COM COMMAND.COM 下列文件丟失或被破壞：WIN.COM和COMMAND.COM
There is an invalid country code or code page in your CONFIG.SYS file 在你的CONFIG.SYS里有一個無效的國家代碼
There is an error in the COUNTRY command in your CONFIG.SYS file 在你的CONFIG.SYS里有一個錯誤的設置國家命令
There is not enough memory for the COUNTRY.SYS file 沒有足夠的內存來加載COUNTRY.SYS文件
Remove some drivers from your CONFIG.SYS file, and then try again 請從CONFIG.SYS文件中刪除部分驅動程序，然后再試
Remove some drivers, and then try again 去除一些驅動程序，然后再試。這里的驅動程序是指在CONFIG.SYS中使用device或devicehigh命令加載的程序文件
Remove some disk drivers from your CONFIG.SYS file, and then try again 從你的(CONFIG.SYS)移去部分程序，然后再試
The configuration specified in your CONFIG.SYS file is too large for memory 調整你的CONFIG.SYS文件以獲得足夠大的內存
You have too many block devices specified in your CONFIG.SYS file 調整你的CONFIG.SYS文件以獲得block devices
The STACKS setting(s) in your CONFIG.SYS file are incorrect 在你的CONFIG.SYS中堆棧設置不正確
Default stack settings will be used instead 缺省的堆棧設置將被替代使用
There is an error in your CONFIG.SYS file on line XX 在你的CONFIG.SYS里XX行錯誤
Warning: Logical drives past Z exist and will be ignored 警告：邏輯驅動器Z已經存在，將被忽略
Type the name of the Command Interpreter (e.g., C:\\WINDOWS\\COMMAND.COM) Press any key to continue… 請輸入命令解釋器的文件名(如：C:\\WIN DOWS\\COMMAND.COM)后，按任意鍵繼續
Windows is bypassing your startup files
Minimal network support will be loaded if available Windows正在跳過你的啟動文件。如果網絡可用，最小網絡支持將被加載
Windows is starting the command prompt only Windows正在啟動命令字符模式
Windows will prompt you to confirm each startup command Windows將提示你確認每一個啟動命令
The compression driver cannot be set up correctly 壓縮驅動程序不能被正確加載
Get a version from your vendor that is compatible with this version of Windows 從你的供應商那里獲得一個與Windows版本相兼容的版本
Process the system registry 運行系統注冊表
Create a startup log file (BOOTLOG.TXT) 創建啟動日志BOOTLOG.TXT文件
Process your startup device drivers (CONFIG.SYS) 運行CONFIG.SYS文件中的設備驅動
Process your startup command file (AUTOEXEC.BAT) 運行AUTOEXEC.BAT中的啟動命令
Load the Windows graphical user interface 裝入WINDOWS圖形用戶界面(GDI)
Warning: Windows has detected a registry/configuration error. Choose, Command prompt only, and run SCANREG 警告：Windows檢測到一個注冊表或配置錯誤選擇DOS操作模式，運行SCANREG
Warning: Windows has detected a compressed drive access error. Choose Safe mode command prompt only, to help you identify the problem 警告：Windows檢測到一個訪問壓縮驅動器錯誤，選擇安全模式下的MS-DOS，來幫助你識別這個問題
Warning: Windows did not finish loading on the previous attempt. Choose Safe mode, to start Windows with a minimal set of drivers 警告：Windows在剛才嘗試后不能夠完成加載，選擇安全模式，用最小驅動啟動你的電腦
Warning: Windows multi-boot may not function correctly
Check for system files in your root directory with conflicting extensions 警告：Windows不能夠正確完成多系統啟動，在你的ROOT目錄里檢查不一致的系統文件
Warning: the system configuration manager failed to run. Some of your real-mode device drivers may not initialize properly 警告：系統管理器運行失敗，一些實模式驅動可能沒有正確初始化
The BUFFERS setting(s) in your CONFIG.SYS file are too large. Default buffer settings will be used instead 在你的CONFIG.SYS里BUFFER設置太大。默認的BUFFER緩沖器設置將被使用
A memory allocation error occurred during startup<BR< p>
>Restart your computer and select Interactive Start to identify the problem 在啟動過程中內存分配發生錯誤，請重新啟動你的計算機然后選用交互式方式啟動來確定故障原因
Warning: the high memory area (HMA) is not available Additional low memory (below 640K) will be used instead 警告：高端內存不可用，低端內存將被代替使用
There is not enough memory for Windows. Remove some drivers from your CONFIG.SYS file, and then try again 對Windows來說沒有足夠的內存，請從CONFIG.SYS文件中移去部分加載的程序，然后再試著啟動你的讀入計算機
Your previous MS-DOS files were not found. 舊的MS-DOS文件沒有找到，這常見于使用雙啟動的系統，另一個系統是DOS6
Your previous MS-DOS version is not supported. MS-DOS startup failed 舊的MS-DOS版本不支持。MS-DOS啟動失敗
Now loading your previous version of MS-DOS, please wait 現在正在加載舊的MS-DOS版本，請等待
Invalid setting in the MSDOS.SYS file:An internal stack overflow has caused this session to be halted MSDOS.SYS文件中無效的設置選項。系統堆棧溢出，系統掛起
Change the STACKS setting in your CONFIG.SYS file, and then try again 請改變CONFIG.SYS文件中的STACK設置，然后再試
Stack overflow 堆棧溢出
Integer divide by 0　 整數被0除
Not enough space for environment　 沒有足夠的空間
Run-time error 運行錯誤
Floating-point support not loaded　 浮點運算支持沒有裝入
Null pointer assignment　 無效的斷點分配